High-Precision Guided-Wheel Flexible Inclinometer高精度柔性测斜仪（导轮版）
Guided-wheel positioning keeps each sensing section aligned with the required measuring direction while the articulated array follows continuous deformation. Built for projects that need both a flexible profile and directional control.导轮定位让各测量节段保持指定测向，柔性阵列同时跟随连续变形。适合既要连续剖面、又要明确方向控制的测斜管项目。
Continuous Profile, Defined Direction连续看形态，也能控制测向
- 010.005 mm/m · ±0.001°
At a 1 m gauge length, high displacement resolution and repeatability reveal small changes between adjacent sections.在 1m 标距下，高位移分辨率和重复性便于识别相邻节段之间的微小变化。
- 02Guided-wheel positioning导轮定位
Mechanical guidance follows the casing direction and reduces uncertainty when the project specifies a principal measuring axis.机械导向沿测斜管方向定位，项目指定主测轴时更容易保持一致。
- 03IP68 / 5 MPaIP68 / 5MPa
Suitable for wet boreholes and long-term installation; 8 MPa protection is available by project configuration.适合潮湿深孔和长期安装；高水压项目可配置 8MPa 版本。
- 04Continuous 3D profile连续三维剖面
The orientations of successive sensing sections are combined to reconstruct the deformation shape along the monitored path.逐节组合各测量节段的空间姿态，重构沿监测路径的连续变形形态。
Measure Section by Section, Reconstruct the Whole Profile逐节测量，重构整条变形剖面
The array combines sensing sections with flexible connections. Each section records its local spatial attitude; the software joins the section vectors in sequence to recover the 3D shape of the borehole or structure. The guided wheels engage the casing grooves, keeping the defined measuring axis consistent as the array follows deformation.阵列由测量节段与柔性连接段组成。每个测量节段记录自身空间姿态，软件按安装顺序连接各节段向量，还原钻孔或结构的三维形态。导轮与测斜管导槽配合，使阵列在跟随变形的同时保持约定测轴。
01 · Sense01 · 逐节感知
Each sensing section measures its local attitude and contributes one point to the deformation profile.每个测量节段记录局部姿态，为变形剖面提供一个连续测点。
02 · Guide02 · 导轮定向
The wheel assemblies follow compatible casing grooves so the principal measuring direction stays traceable along the run.导轮组件沿兼容导槽运行，使主测方向在整条监测路径上保持可追溯。
03 · Reconstruct03 · 连续重构
The system combines the sections in sequence to produce the 3D shape and displacement profile relative to the selected baseline.系统按顺序组合各节段数据，输出相对于选定基准的三维形态与位移剖面。
From Individual Readings to a Continuous Deformation History从单节读数到连续变形历程
A single reading describes the complete profile at one moment. Comparing subsequent readings with the initial or designated baseline shows where deformation is concentrated, how it develops and whether the direction changes along the monitored path.一次采集得到某一时刻的完整剖面；将后续数据与初始基准或指定基准比较，可查看变形集中位置、发展过程及沿监测路径的方向变化。
3D Deformation Curve三维变形曲线
View the reconstructed spatial shape of the full monitored length rather than isolated angle readings.直接查看整段监测范围的空间形态，而不是一组彼此孤立的角度读数。
Section-by-Section Displacement逐节位移剖面
Locate the depth or chainage where the curve changes and identify the deformation zone along the array.沿阵列定位曲线发生变化的深度或里程，识别主要变形区段。
Multi-Period Comparison多期趋势对比
Overlay readings from different times to follow the magnitude, rate and direction of ongoing deformation.叠加不同时段的监测结果，观察变形幅值、发展速度和方向变化。
Vertical, Horizontal or Ring — with a Compatible Guide Path垂直、水平或环形布设，均需匹配导向路径
The flexible array can follow straight or curved monitoring routes. On this version, the guide-wheel assemblies must run inside compatible continuous grooves; casing geometry, clearances and bend transitions are checked before the final configuration is confirmed.柔性阵列可沿直线或曲线路径布设。导轮版需要导轮组件在兼容且连续的导槽中运行，正式选型前应核对管体结构、配合间隙和弯曲过渡。
Vertical · Deep Displacement垂直布设 · 深层位移
Installed in grooved inclinometer casing for foundation pits, slopes and other borehole profiles. The guide wheels maintain the selected axis through the depth.安装于带导槽测斜管，用于基坑、边坡等深层位移剖面；导轮沿孔深保持选定测轴。
Horizontal · Settlement Profile水平布设 · 沉降剖面
A compatible grooved guide conduit is laid along the monitoring line. The completed array follows the route to describe differential settlement by chainage.沿监测线布设兼容的带导槽导管，阵列随线路延伸，按里程反映差异沉降。
Ring · Section Convergence环形布设 · 断面收敛
For tunnel or cavern sections, a continuous guided path can be arranged around the lining. Route curvature and passage clearance require project-specific verification.可在隧道或洞室衬砌周边设置连续导向路径，形成断面收敛监测；路径曲率与通行间隙需按项目核验。
The guide path is part of the measuring system导向路径也是测量系统的一部分
Groove direction, continuity and cleanliness directly affect installation and directional consistency. Confirm the casing or guide-conduit details before production.导槽方向、连续性和洁净度会直接影响安装与测向一致性，生产前需确认测斜管或导管资料。
A Complete Chain from the Borehole to the Monitoring Screen从孔内阵列到监测界面的完整链路
The sensor string is only one part of the system. A project configuration also accounts for the guide path, acquisition, power, communication and the required data presentation.传感器串只是系统的一部分。完整项目还需同时确定导向路径、采集、供电、通信以及数据展示方式。
Sensing sections and flexible connections follow the monitored route and provide the profile data.测量节段与柔性连接段沿监测路径布置，提供连续剖面数据。
Wheel assemblies engage compatible grooves to preserve the specified measuring direction.导轮组件与兼容导槽配合，保持项目约定的主测方向。
A project-matched controller powers the array, schedules readings and stores the field data.按项目配置控制器，为阵列供电、执行采样并保存现场数据。
Local or remote access is configured around the site's network and monitoring-platform requirements.根据现场网络与监测平台要求，配置本地或远程数据访问方式。
Check the Guide Path First, Then Install in Sequence先检查导向路径，再按节段顺序安装
A smooth installation depends on the casing as much as on the array. Record the groove selected as the principal axis, inspect the full passage and keep the section order unchanged from assembly through baseline acquisition.导轮版能否顺利安装，与测斜管状态同样相关。进场时应记录作为主测轴的导槽，检查整条通道，并从组装到基准采集始终保持节段顺序不变。
Before lowering or pulling下放或牵引前
- 1Confirm compatibility核对兼容性
Confirm casing diameter, groove geometry, direction, joints and planned route against the guide-wheel configuration.核对管径、导槽结构与方向、接头和计划路径是否与导轮配置相符。
- 2Clear the complete passage检查整条通道
Check groove continuity and remove sediment, burrs, joint offsets or obstructions that could catch a wheel assembly.检查导槽是否连续，清理可能卡住导轮的沉积物、毛刺、接头错台或障碍物。
- 3Inspect the array检查阵列
Verify section sequence, connectors, cables and wheel movement before the array enters the guide path.入管前检查节段顺序、连接部位、线缆及导轮转动状态。
During installation and commissioning安装与调试阶段
- 1Align the measuring axis对准主测方向
Set each wheel assembly into the designated groove and keep the same axis convention along the full run.将各导轮组件对准指定导槽，整条阵列采用同一测轴约定。
- 2Advance steadily匀速下放或牵引
Move the array smoothly without twisting, impact or forced passage. Stop and inspect whenever resistance rises abnormally.保持平稳，避免扭转、冲击和强行通过；阻力异常增大时应停下检查。
- 3Fix, test and establish the baseline固定、通测并建立基准
Protect the lead-out, confirm communications and section data, then acquire the project baseline after the installation state is stable.保护出线端，核查通信与各节数据，待安装状态稳定后采集项目基准。
For Continuous Profiles with a Defined Measuring Direction适合既要连续剖面、又要明确测向的监测任务
The guided-wheel version is particularly useful where a principal displacement direction has been defined in the monitoring design and a compatible guided path can be installed.监测设计已经明确主位移方向、现场又能布置兼容导向路径时，导轮版更容易形成稳定、可对比的连续剖面。
Retaining-Wall Profiles围护结构位移剖面
Observe the location and development of lateral deformation along the depth of a grooved casing during excavation and support stages.在开挖和支护阶段，沿带导槽测斜管查看侧向变形的位置及其沿深度的发展。
Potential Sliding-Zone Tracking潜在滑动带跟踪
Use the continuous borehole profile to identify where displacement concentrates and compare its evolution across monitoring periods.从连续孔内剖面识别位移集中区，并对比不同监测期的变化趋势。
Stations, Tunnels & Adjacent Works车站、隧道及邻近施工
Track directional deformation where construction influence needs to be resolved by depth or chainage.用于施工影响需按深度或里程分析的场景，持续跟踪指定方向的变形。
Differential Settlement Profile差异沉降剖面
With a compatible horizontal guide conduit, monitor settlement changes continuously along the alignment.配合兼容的水平导向管，连续观察沿线路方向的沉降差异。
Section Convergence断面收敛
Arrange a project-verified ring guide path around the section to follow circumferential shape changes.沿断面设置经项目核验的环形导向路径，跟踪周向形态变化。
Wet or Pressurized Boreholes潮湿或承压深孔
Standard IP68 / 5 MPa protection covers routine wet installations; specify the 8 MPa option when the design water pressure requires it.常规潮湿环境采用 IP68 / 5MPa；设计水压更高时可按项目配置 8MPa 版本。
Confirmed Performance and Configuration Scope已确认性能与配置范围
Values below apply to the guided-wheel version. Mechanical matching and system accessories are finalized from project inputs.下表参数适用于导轮版；机械配合和系统附件根据项目输入最终确定。
| Parameter参数 | Specification规格 | Engineering note工程说明 |
|---|---|---|
| Displacement resolution位移分辨率 | 0.005 mm/m at 1 m gauge length（1m 标距） | Use the same gauge basis when comparing product options选型比较时统一按 1m 标距口径 |
| Repeatability重复性 | ±0.001° | Describes consistency across repeated readings表示多次重复读数的一致性 |
| Standard protection标准防护 | IP68 / 5 MPa | For wet boreholes and long-term embedded monitoring面向潮湿孔内和长期埋设监测 |
| High-pressure option高水压选项 | 8 MPa | Available by project configuration可按项目配置 |
| Guidance导向方式 | Guided-wheel positioning导轮定位 | Casing or guide-conduit compatibility must be confirmed需确认测斜管或导管兼容性 |
| Profile output剖面输出 | Continuous 3D shape and displacement profile连续三维形态与位移剖面 | Reconstructed section by section relative to the selected baseline逐节重构，并与选定基准比较 |
| Deployment布设方式 | Vertical / horizontal / ring垂直 / 水平 / 环形 | Subject to a compatible continuous guide path and route verification需具备兼容的连续导向路径，并核验布设线路 |
Six Inputs Define the Project Configuration提供六类信息，即可开始项目配置
This version is configured by project. No separate SKU is assigned on this page.本版本按项目配置，本页不设置独立 SKU。
| Input选型输入 | What to confirm需要确认 | Why it matters影响什么 |
|---|---|---|
| Monitoring route监测路径 | Depth or length, vertical / horizontal / ring layout and access at each end孔深或长度、垂直 / 水平 / 环形布设及两端作业条件 | Array length, installation method and lead-out arrangement阵列长度、安装方式和出线安排 |
| Casing & grooves管体与导槽 | Internal diameter, groove geometry, direction, joint form and continuity内径、导槽结构与方向、接头形式和连续性 | Wheel matching, passage clearance and defined measuring axis导轮匹配、通行间隙和主测方向 |
| Deformation profile预计变形 | Expected direction, magnitude, concentrated zone and route curvature预计方向、幅值、集中区段和路径曲率 | Section arrangement and route verification节段布置和线路核验 |
| Measurement detail测量细节 | Required spatial detail and the engineering zones that need closer observation所需空间细节及需要重点观察的工程区段 | Measurement-section arrangement and local densification测量节段安排与局部加密 |
| Environment环境条件 | Water pressure, temperature, corrosion exposure and installation duration水压、温度、腐蚀条件和安装年限 | 5 or 8 MPa protection and project-specific protection details5MPa 或 8MPa 防护及项目防护细节 |
| Data & site services数据与现场条件 | Reading interval, power, network, local access and platform requirements采集周期、供电、网络、本地访问及平台要求 | Acquisition, storage and communication configuration采集、存储和通信配置 |
Choose the guided-wheel version when这些情况优先选择导轮版
The project specifies a principal measuring direction, uses a compatible grooved casing or guide conduit, and needs the array to preserve that direction along a continuous profile.项目已经明确主测方向，现场采用兼容的带导槽测斜管或导管，并希望阵列沿连续剖面保持该测向。
Confirm the standard flexible version when这些情况可对比标准柔性版
The installation path has no suitable guide grooves, prioritizes free-form curved placement, or does not require mechanical orientation along a defined axis.安装路径没有适配导槽，更侧重自由曲线布设，或无需用机械结构保持指定测向时，可与标准柔性版比较。
Questions Before Configuration配置前常见问题
What is the main difference from the standard flexible inclinometer?与标准高精度柔性测斜仪的主要区别是什么？
Can an existing inclinometer casing be reused?可以直接使用已有测斜管吗？
Does 8 MPa apply to every order?所有订单都是 8MPa 吗？
What information should be sent for a configuration proposal?申请配置方案时需要提供什么？
Need a guided-wheel configuration?需要导轮版配置建议？
Provide the monitoring length, casing or guide-conduit details, water pressure and required measuring direction.提供监测长度、测斜管或导管资料、水压和主测方向，即可开始选型。